Antena Voyager Maritima MFV-8MH

 

40,00
Câmbio: 1 US$ = (3.60)
R$ 144,00
QTD
Adicionar ao meu orçamento
 
 
2170 views
Código do produto: 24778

Descrição do produto

SPECIAL FEATURES

* This is a superior 6 dB gain 8 feet antenna.



* Operates on all USA and international VHF marine frequency.



* Extended frequency coverage to 162 MHz for NOAA 162 MHz weather

reports.



* No need for elaborate ground system-works equally well on fiberglass, or

wood boat.



ANTENNA CABLE

The white coax cable (RG 58 U) is preassembled with a PL -259 connector.



DO NOT CUT OR COIL CABLE, if required, the cable can be lengthened with

suitable connectors and 52 ohm (RG 58 U or RG 8 ) impedance coax cable

without any detrimental effects on the antenna.



SWIVEL BASE ASSEMBLY

We recommend assembling the MFV-8 swivel base.

Once assembled, you can decide where you want

to mount it.

The dual swivels allow you to fold over or lay down the antenna just by using the single

lever.

The second swivel allows for mounting the plate vertically or horizontally or a variety of positions

in between.



Refer to the exploded drawing.



A.

Put bolt (10) through the flat side of the rotation hub (3) and into the base plate (9) as shown.

Place

a washer (8) and nut (7) on the bolt.

Hand tighten the nut at this time.



B.

Put bolt (1) through the level bar (2) and continue through to top part of rotation hub (3) into the

rotation mount (4).

Rotation mount (4) has a threaded portion.

You must screw bolt (1) into the

threaded section of the rotation mount.

First screw the bolt all the way in.

Then back the bolt out

1-13/4 turns.



NOTE: If you fail to back the bolt out 1-13/4 turns the fold over lever will not work.



Now place washer (5) and nut (6) on bolt (1) and tighten.

DO NOT SCREW THE BOLT HEAD IN.

KEEP

IT STATIONARY AND TIGHTEN THE NUT ONLY.

Tighten the assembly by moving the lever

counter-clockwise.



Mount your base plate in a desired location.

Using the bolt (11) assembly loosen bolt (10) and adjust

the unit so that the threaded portion is vertical.

Tighten bolt (10).



Screw the 5’ fiberglass mast onto the swivel base.

Route the coaxial cable to your radio.

Most people

route the cable through the hull.

DO NOT CUT OFF ANY EXCESS CABLE.

Simply coil it in a 8-12”

loop behind the radio.



PL259 connectors are very susceptible to corrosion.

We strongly recommend use of protectant

coatings to prevent corrosion.

Corrosion of the connector could case radio failure.

Periodic

maintenance may be required.



Waterproof the hole for the coaxial cable and your mount with standard marine sealant.

The bolts,

washers, and nuts used on the MFV-8 are stainless steel.

A light coating of protectant will MINIMIZE

oxidation in heavy salt spray.



To lay your antenna over (fold down), simply turn the lever clockwise.

This will release the rotation hub

from the mount and should allow you to move the antenna to the horizontal position.

If bolt (1) is too

loose, your antenna could fall over when the lever is released.

If bolt (1) is too tight , your antenna may

not fold over.

To adjust this, hold the bolt in position and loosen unt (6) .

To adjust for a too loose

condition , screw bolt (1) in a 1/4-1/2 turn.

Once adjusted, hold bolt (1) in a steady position and tighten

nut (6).

Reverse this process if bolt (1) is too tight.



Your MFV-8 is pretuned for maximum gain and no electrical adjustment should be necessary.

Installation

is complete now.



Parts Description

1 & 10 Hex Bolt

2 Lever Bar

3 Rotation Hub

4 Rotation Mount

5&8 Washers

6&7 Nuts

11 Mounting Bolts/Hardware(4 sets)

12 S.

S.

Spring

 

Garantia

Consulte um de nossos vendedores sobre disponibilidade de estoque e garantia.

As especificações dos produtos são fornecidas pelo fabricante havendo variações de características do produto conforme o número do lote. NÃO FAZEMOS ENTREGAS NO BRASIL.

Preços em dólar sem IVA sujeitos a alteração sem aviso prévio, clientes paraguaios necessitam pagar IVA.